Axis Q6035-E User Manual Page 39
- Page / 50
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
AXIS Q6035–E PTZ Dome Network Camera
System Options
Note
The initial password can only be set once. If the password is lost, the Axis product must be reset to factory default, see
Reset to factory default s ettings, on page 41
.
UPnP
TM
The Axis product includes supp ort for UPnP
TM
.UPnP
TM
is enabled by default and the p roduct is automatically detected by operating
systems and clients that support this protocol.
UPnP
TM
can be d isabled under System Options > Network > UPnP
TM
.
RTP/H.264
The RTP p ort range and multicast settings are configured under System Options > Network > RTP.
The RTP port range defines the range of ports from which the video ports are automatically selected. For multicas t streams, only
certain IP addresses and port numbers should be used.
Bonjour
The Axis product includes support for Bonjour. Bonjour is enabled by default and the product is automatically detected by operating
systems and clients that support this protocol.
Bonjour can be disabled under System Options > Network > Bonjour.
Storage
SD Card
The SD/SDHC memory card (not included) is managed on the System Options > Storage > SD Card page.
The settings under Storage Device are used to identify and monitor the status of the SD card, and to unmount the SD card
before removal. Mounting is done automatically when a card is inserted. S D cards are normally preformatted when purchased,
but if needed, click Format to format the card.
Note
To prevent corruption of recordings, the SD card should always be unmounted before removal.
If the card’s status shows as failed, click Check disk to see if the problem can be found and then try Repair.
The settings under Storage D evice Settings are used to configure removal of recorded video. Automatic disk cleanup can be enabled
and set according t o a schedule. The disk can be locked to prevent removal of recordings.
For more information, see
theonlinehelp
.
Maintenance
The Axis produ
ct provides several maintenance functions. These are available under System Options > Maintenance.
Click Re
start to perform a correct restart if the Axis product is not behaving as expected. This will not affect any of the current
settings.
Click Restore to reset most settings to the factory default values. The following settings a re not affected:
• the boot protocol (DHCP or static)
• the static IP address
• the default router
39
- USER MANUAL 1
- Table of contents 3
- Hardware overview 4
- Connectors 4
- LED indicators 5
- Accessing the product 6
- Access from a browser 6
- Access from the Internet 7
- Set the root password 7
- The Live View page 8
- Media streams 10
- How to stream H.264 10
- AXIS Media Control (AMC) 10
- Setting up the p roduct 13
- Setting up the product 13
- Basic Setup 13
- Video Stream 14
- Camera Settings 15
- Stream Profiles 15
- White balance 16
- Wide Dynamic Range 16
- Exposure Settings 16
- Image settings 16
- Privacy Mask 17
- Live View Config 18
- PTZ (Pan Tilt Zoom) 20
- Preset positions 20
- Autotracking 20
- Guard Tour 21
- OSDI Zones 22
- Advanced 23
- Control Queue 23
- Applications 25
- Event Se rvers 26
- Event Types 27
- Gatekeeper 28
- Set up motion detection 29
- Motion detection parameters 29
- Recordings 31
- Event recordings 31
- Continuous recording 32
- System Options 33
- Security 33
- Date & Time 34
- Maintenance 39
- Troubleshooting 43
- Checking the firmware 43
- Upgrading the firmware 43
- Emergency recovery procedure 43
- Technical Specifications 47
- Performance considerations 49
Related products and manuals for Security cameras Axis Q6035-E
Security cameras Axis M7001 User Manual
(46 pages)
(46 pages)
Security cameras Axis Q8722-E Installation Guide
(104 pages)
(104 pages)
Security cameras Axis 214 PTZ User Manual
(53 pages)
(53 pages)
Security cameras Axis Q1755 User Manual
(53 pages)
(53 pages)
Security cameras Axis Q1921-E User Manual
(54 pages)
(54 pages)
Security cameras Axis 0270-002 Datasheet
(4 pages)
(4 pages)
Security cameras Axis 215 PTZ User Manual
(56 pages)
(56 pages)
Security cameras Axis P1355 User Manual
(63 pages)
(63 pages)
Security cameras Axis M2014-E User Manual
(50 pages)
(50 pages)
Security cameras Axis M1113-E User Manual
(50 pages)
(50 pages)
Security cameras Axis P1357 User Manual
(64 pages)
(64 pages)
Security cameras Axis P1204 User Manual
(48 pages)
(48 pages)
Security cameras Axis Q1932-E User Manual
(57 pages)
(57 pages)
Security cameras Axis 207W User Manual
(63 pages)
(63 pages)
© 2020, manymanuals.com. All rights reserved. | 3.105 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals