Axis 7100 Service Manual Page 32
- Page / 74
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
II.4 Parameter description
A brief description of the parameters is given. Detailed explanations can be found in the
operating manual for BS7200.
II.4.1 General
Motor pole no. [-]
The current setpoint entry can be adjusted for operating 2- to 12-pole motors.
Changes are only possible when the Enable signal is inactive.
Language [-]
The operator language can be selected from: English, German, French.
Resolver pole-no. [-]
Switches the no. of resolver poles to operate 2/4/6-pole resolvers.
Changes are only possible when the Enable signal is inactive.
I/O [-]
Determines the function of the I/O terminal X3/15, see Chapter III.1.2 and III.2.2.
Ballast resistor [-]
Switches between internal and external ballast resistor.
Ballast power [W]
Sets the external ballast power.
Brake [-]
The motor holding brake can be operated from the servo amplifier.
NI-offset [increment]
Only accessible when the interface is set to ROD. Determines the position of the zero pulse
within a turn. Input referred to zero crossing of the resolver and the preset resolution
ROD/SSI [-]
Select the type of interface or switch off the interface.
ROD code [-]
Only accessible when the interface is set to ROD. Determines whether the output is in decimal
or binary code.
Resolution [Inkr./Umdr.]
Only accessible when the interface is set to ROD. Determines the no. of increments per turn
which are output.
SSI code [-]
Only accessible when the interface is set to SSI. Determines whether the output is in binary
or GRAY-code.
SSI clock [kHz]
Only accessible when the interface is set to SSI. Determines the SSI clock rate and the
quiescent level of the clock line. Setting : 200, 1500, 200 inverted, 1500 inverted.
neue seite
Page II - 16 Installation and commissioning Chapter II
01.98 digifas™ 7100 series
- Digital Servodrive 1
- Mat. no. 83498 2
- Contents 3
- Contents Diagram Page 3
- Safety instructions 5
- Directives and standards 6
- -conformance 6
- I General 7
- I.1 About this manual 7
- I.4 Nameplate 8
- I.5 Equipment description 9
- - A.4.012.4/26 11
- Chapter I General Page I - 5 11
- - A.4.012.4/14 12
- Page I - 6 General Chapter I 12
- - A.4.012.4/38 13
- Chapter I General Page I - 7 13
- Page I - 8 General Chapter I 14
- 01.98 digifas™ 7100 series 14
- Chapter I General Page I - 9 15
- I.10 System grounds 16
- I.11 Ballast circuit 16
- II.1 Important instructions 17
- - A.4.012.1/3 20
- - A.4.012.1/2 21
- - A.4.012.1/8 22
- - A.4.012.1/5 23
- - A.4.012.1/6 24
- - A.4.012.4/27 25
- - A.4.012.4/35 26
- - A.4.029.4/1 27
- A.4.029.4/2 28
- II.3 Commissioning 30
- II.4 Parameter description 32
- II.4.1 General 32
- II.4.2 Current controller 33
- II.4.3 Speed controller 33
- II.4.4 Service functions 34
- II.4.5 Display actual value 34
- III.1 Input functions 35
- III.1.1 Analog inputs 35
- III.2 Output functions 36
- III.2.1 Analog outputs 36
- III.2.2 Digital outputs 36
- III.2.3 Brake 37
- IV Interfaces and options 39
- IV.3 PC interface 41
- - A.4.012.3/1 43
- IV.5.2 Important notes 45
- IV.5.3 Commissioning 46
- - A.4.011.1/15 47
- V Drawings 49
- - A.4.011.1/7 50
- Page V - 2 Drawings Chapter V 50
- - A.4.011.1/8 51
- Chapter V Drawings Page V - 3 51
- - A.4.012.4/30 52
- Page V - 4 Drawings Chapter V 52
- - A.4.012.4/28 53
- Chapter V Drawings Page V - 5 53
- - A.4.012.4/36 54
- Page V - 6 Drawings Chapter V 54
- - A.4.012.4/37 55
- Chapter V Drawings Page V - 7 55
- - A.4.011.4/26 56
- Page V - 8 Drawings Chapter V 56
- - A.4.012.4/29 57
- Chapter V Drawings Page V - 9 57
- - E.4.947.4/21 58
- - A.4.012.4/31 59
- - A.4.012.4/32 60
- - A.4.012.4/33 61
- VI Appendix 63
- - A.4.012.1/4 64
- - A.4.012.1/9 66
- VI.4 Fault-finding 68
- VI.5 Glossary 70
- VI.6 Parameter list 72
- VI.7 Index 73
Related products and manuals for Servers Axis 7100
Servers Axis 7100 Installation Guide
(424 pages)
(424 pages)
Servers Axis 70 User's Guide
(24 pages)
(24 pages)
Servers Axis 24HUM Instruction Manual
(80 pages)
(80 pages)
Servers Axis 7000/FX User Manual
(134 pages)
(134 pages)
Servers Axis NAS 100 User Manual
(108 pages)
(108 pages)
Servers Axis 950 User Manual
(69 pages)
(69 pages)
Servers Axis APPINT User Manual
(10 pages)
(10 pages)
Servers Axis 70U User Manual
(26 pages)
(26 pages)
Servers Axis 700 User Manual
(2 pages)
(2 pages)
Servers Axis E100 Installation Manual
(27 pages)
(27 pages)
© 2020, manymanuals.com. All rights reserved. | 0.088 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals