Axis 7100 Service Manual Page 63
- Page / 74
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
VI Appendix
VI.1 Delivery package, transport, storage, maintenance, disposal
Delivery — 1 digifas™ 7100 series servo amplifier
package : — 3.5" diskette with the operator software BS7200
— 2 ring cores
— installation/commissioning manual for digifas™ 7100
— BS7200 operating manual
— installation/commissioning manual for the CONNECT module,
if one is built in
Transport : — only by qualified personnel
— only in the original recyclable manufacturer’s packaging
— avoid shocks
— the servo amplifiers contain electrostatically-sensitive components,
which can be damaged by incorrect handling.
Discharge yourself before you touch the servo-amplifier.
Avoid touching highly insulating materials (artificial fabrics,
plastic wrappings etc.). Place the servo amplifier on a conductive base.
— if the packaging is damaged, check the unit for visible damage. In such
a case inform the shipper and the manufacturer.
Storage : — only in the original recyclable manufacturer’s packaging
— the servo amplifiers contain electrostatically-sensitive components,
which can be damaged by incorrect handling.
Discharge yourself before you touch the servo-amplifier.
Avoid touching highly insulating materials (artificial fabrics,
plastic wrappings etc.). Place the servo amplifier on a conductive base.
— max. stacking height digifas™ 7103...7116 : 10 cartons
digifas™ 7133...7150 : 5 cartons
— storage temperature –25 ... +85°C, max. 20°/hr variation
— humidity relative humidity max. 95% no condensation
— storage duration < 1 year without restriction
> 1 year : the capacitors must be re-formed before
commissioning the servo amplifier.
To do this: remove all electrical connections,
feed the servo amplifer for about 30 min
from single-phase 230V AC on terminals L1 / L2.
Maintenance : — no maintenance required
— opening the equipment housing invalidates the guarantee
Cleaning : — if the housing is dirty : clean with isopropanol or similar
do not immerse or spray
— if there is dirt inside the unit : to be cleaned by the manufacturer
— if the fan screen is dirty : clean with a dry brush
Disposal : — the servo amplfier may be reduced to its principal components by
undoing all screw connections (aluminium heat sink and front panel,
steel housing sections, electronics boards)
— the disposal should be performed by a certified disposal company.
We can give you suitable addresses.
neue seite
Chapter VI Appendix Page VI - 1
digifas™ 7100 series 01.98
- Digital Servodrive 1
- Mat. no. 83498 2
- Contents 3
- Contents Diagram Page 3
- Safety instructions 5
- Directives and standards 6
- -conformance 6
- I General 7
- I.1 About this manual 7
- I.4 Nameplate 8
- I.5 Equipment description 9
- - A.4.012.4/26 11
- Chapter I General Page I - 5 11
- - A.4.012.4/14 12
- Page I - 6 General Chapter I 12
- - A.4.012.4/38 13
- Chapter I General Page I - 7 13
- Page I - 8 General Chapter I 14
- 01.98 digifas™ 7100 series 14
- Chapter I General Page I - 9 15
- I.10 System grounds 16
- I.11 Ballast circuit 16
- II.1 Important instructions 17
- - A.4.012.1/3 20
- - A.4.012.1/2 21
- - A.4.012.1/8 22
- - A.4.012.1/5 23
- - A.4.012.1/6 24
- - A.4.012.4/27 25
- - A.4.012.4/35 26
- - A.4.029.4/1 27
- A.4.029.4/2 28
- II.3 Commissioning 30
- II.4 Parameter description 32
- II.4.1 General 32
- II.4.2 Current controller 33
- II.4.3 Speed controller 33
- II.4.4 Service functions 34
- II.4.5 Display actual value 34
- III.1 Input functions 35
- III.1.1 Analog inputs 35
- III.2 Output functions 36
- III.2.1 Analog outputs 36
- III.2.2 Digital outputs 36
- III.2.3 Brake 37
- IV Interfaces and options 39
- IV.3 PC interface 41
- - A.4.012.3/1 43
- IV.5.2 Important notes 45
- IV.5.3 Commissioning 46
- - A.4.011.1/15 47
- V Drawings 49
- - A.4.011.1/7 50
- Page V - 2 Drawings Chapter V 50
- - A.4.011.1/8 51
- Chapter V Drawings Page V - 3 51
- - A.4.012.4/30 52
- Page V - 4 Drawings Chapter V 52
- - A.4.012.4/28 53
- Chapter V Drawings Page V - 5 53
- - A.4.012.4/36 54
- Page V - 6 Drawings Chapter V 54
- - A.4.012.4/37 55
- Chapter V Drawings Page V - 7 55
- - A.4.011.4/26 56
- Page V - 8 Drawings Chapter V 56
- - A.4.012.4/29 57
- Chapter V Drawings Page V - 9 57
- - E.4.947.4/21 58
- - A.4.012.4/31 59
- - A.4.012.4/32 60
- - A.4.012.4/33 61
- VI Appendix 63
- - A.4.012.1/4 64
- - A.4.012.1/9 66
- VI.4 Fault-finding 68
- VI.5 Glossary 70
- VI.6 Parameter list 72
- VI.7 Index 73
Related products and manuals for Servers Axis 7100
Servers Axis 7100 Installation Guide
(424 pages)
(424 pages)
Servers Axis 70 User's Guide
(24 pages)
(24 pages)
Servers Axis 24HUM Instruction Manual
(80 pages)
(80 pages)
Servers Axis 7000/FX User Manual
(134 pages)
(134 pages)
Servers Axis NAS 100 User Manual
(108 pages)
(108 pages)
Servers Axis 950 User Manual
(69 pages)
(69 pages)
Servers Axis APPINT User Manual
(10 pages)
(10 pages)
Servers Axis 70U User Manual
(26 pages)
(26 pages)
Servers Axis 700 User Manual
(2 pages)
(2 pages)
Servers Axis E100 Installation Manual
(27 pages)
(27 pages)
© 2020, manymanuals.com. All rights reserved. | 0.259 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals