Axis 7100 Service Manual Page 34
- Page / 74
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
II.4.4 Service functions
The service functions are help functions for optimizing the controller parameters.
Constant speed
Drive runs with constant speed. The analog setpoint input is inoperable.
Constant current
Drive runs with constant current, under current control. Actual current is the phase current
(combined active and reactive currents). The analog setpoint input is inoperable.
Reversing mode
Drive runs in reversing mode. The analog setpoint input is inoperable.
II.4.5 Display actual value
Ambient temperature
The internal temperature is measured in the servo amplifier and displayed here in °C.
Heat sink temperature
The temperature of the heat sink is measured in the servo amplifier and displayed here in °C.
Intermediate circuit voltage
The intermediate circuit voltage which is produced in the servo amplifier is measured and dis
-
played in V.
I
t
The momentary effective loading is displayed in % of the preset rms value.
Ballast power
The actual ballast power is measured and displayed in W.
Speed
The actual speed of the motor is displayed in rev min
Current: actual value
The momentary value of the rms output current (active component) in A
Rotational angle
Displays the actual rotational angle of the rotor (only forn<20min
) in °mech and counts, re
-
ferred to the mechanical zero point of the measuring system.
Operating time
Counts the hours of operation of the servo amplifier.
II.5 Fault signals, BTB signal
All fault messages are signalled by the red collective display LED on the front panel
and displayed on the screen or the LCD display.
All faults result in opening of the BTB contact and a switch-off of the output stage.
— undervoltage in intermediate circuit : limit set to 65V by the manufacturer
— overvoltage in intermediate circuit : limit set to 750V by the manufacturer
— output stage fault : fault in the output stage
— mains-BTB : at least two phases of the mains are missing
— aux. voltage fault : internal aux. voltage not correct
— heat sink temperature too high : limit set to 80°C by the manufacturer
— Internal temperature too high : limit set to 70°C by the manufacturer
— motor temperature too high : limit set to 145°C by the manufacturer
— brake fault : short-circuit
— resolver error : cable break or similar
Page II - 18 Installation and commissioning Chapter II
01.98 digifas™ 7100 series
- Digital Servodrive 1
- Mat. no. 83498 2
- Contents 3
- Contents Diagram Page 3
- Safety instructions 5
- Directives and standards 6
- -conformance 6
- I General 7
- I.1 About this manual 7
- I.4 Nameplate 8
- I.5 Equipment description 9
- - A.4.012.4/26 11
- Chapter I General Page I - 5 11
- - A.4.012.4/14 12
- Page I - 6 General Chapter I 12
- - A.4.012.4/38 13
- Chapter I General Page I - 7 13
- Page I - 8 General Chapter I 14
- 01.98 digifas™ 7100 series 14
- Chapter I General Page I - 9 15
- I.10 System grounds 16
- I.11 Ballast circuit 16
- II.1 Important instructions 17
- - A.4.012.1/3 20
- - A.4.012.1/2 21
- - A.4.012.1/8 22
- - A.4.012.1/5 23
- - A.4.012.1/6 24
- - A.4.012.4/27 25
- - A.4.012.4/35 26
- - A.4.029.4/1 27
- A.4.029.4/2 28
- II.3 Commissioning 30
- II.4 Parameter description 32
- II.4.1 General 32
- II.4.2 Current controller 33
- II.4.3 Speed controller 33
- II.4.4 Service functions 34
- II.4.5 Display actual value 34
- III.1 Input functions 35
- III.1.1 Analog inputs 35
- III.2 Output functions 36
- III.2.1 Analog outputs 36
- III.2.2 Digital outputs 36
- III.2.3 Brake 37
- IV Interfaces and options 39
- IV.3 PC interface 41
- - A.4.012.3/1 43
- IV.5.2 Important notes 45
- IV.5.3 Commissioning 46
- - A.4.011.1/15 47
- V Drawings 49
- - A.4.011.1/7 50
- Page V - 2 Drawings Chapter V 50
- - A.4.011.1/8 51
- Chapter V Drawings Page V - 3 51
- - A.4.012.4/30 52
- Page V - 4 Drawings Chapter V 52
- - A.4.012.4/28 53
- Chapter V Drawings Page V - 5 53
- - A.4.012.4/36 54
- Page V - 6 Drawings Chapter V 54
- - A.4.012.4/37 55
- Chapter V Drawings Page V - 7 55
- - A.4.011.4/26 56
- Page V - 8 Drawings Chapter V 56
- - A.4.012.4/29 57
- Chapter V Drawings Page V - 9 57
- - E.4.947.4/21 58
- - A.4.012.4/31 59
- - A.4.012.4/32 60
- - A.4.012.4/33 61
- VI Appendix 63
- - A.4.012.1/4 64
- - A.4.012.1/9 66
- VI.4 Fault-finding 68
- VI.5 Glossary 70
- VI.6 Parameter list 72
- VI.7 Index 73
Related products and manuals for Servers Axis 7100
Servers Axis 7100 Installation Guide
(424 pages)
(424 pages)
Servers Axis 70 User's Guide
(24 pages)
(24 pages)
Servers Axis 24HUM Instruction Manual
(80 pages)
(80 pages)
Servers Axis 7000/FX User Manual
(134 pages)
(134 pages)
Servers Axis NAS 100 User Manual
(108 pages)
(108 pages)
Servers Axis 950 User Manual
(69 pages)
(69 pages)
Servers Axis APPINT User Manual
(10 pages)
(10 pages)
Servers Axis 70U User Manual
(26 pages)
(26 pages)
Servers Axis 700 User Manual
(2 pages)
(2 pages)
Servers Axis E100 Installation Manual
(27 pages)
(27 pages)
© 2020, manymanuals.com. All rights reserved. | 0.501 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals